North America Tilt Sensor Market Forecast to 2028 - COVID-19 Impact and Regional Analysis By Material (Metal and Non-Metal), Technology (Force Balance, MEMS, and Fluid Filled), and Industry (Mining & Construction, Consumer Electronics, Industrial, Automot

North America Tilt Sensor Market Forecast to 2028 - COVID-19 Impact and Regional Analysis By Material (Metal and Non-Metal), Technology (Force Balance, MEMS, and Fluid Filled), and Industry (Mining & Construction, Consumer Electronics, Industrial, Automotive, Aerospace, and Others)

The North America tilt sensor market is expected to reach US$ 108.03 million by 2028 from US$ 75.69 million in 2021. It is estimated to grow at a CAGR of 5.2% from 2021 to 2028. Key factors contributing to the market growth are rise in demand for tilt sensors based on MEMS technology and upsurge in demand for construction equipment. However, high cost of tilt sensors based on force balance technology may hamper the market growth.

Tilt sensors have been widely used in many applications, such as instrumentation leveling, oil drilling and structural health monitoring. With the rapid development of the micro-electromechanical system (MEMS) technology. MEMS accelerometer-based high-performance tilt sensors are capable of replacing conventional tilt sensors in most application domains, owing to the rapid development of micro-electromechanical system (MEMS) technology. MEMS resonant accelerometers (MRAs) with high sensitivity are completely qualified for tilt sensing. MRA chips, on the other hand, must be vacuum packaged and require complicated circuits, making them difficult to miniaturize and sell. For low-cost, high-sensitivity, low power consumption, and downsizing, the suggested MEMS sensor uses simplified fabrication procedures, an area-change-based capacitive displacement transducer, and a capacitance-to-voltage conversion application-specific integrated circuit (ASIC). Many industrial and commercial applications, such as mobile phone motion sensors and car airbags, have demonstrated this operating concept. Low-grade accelerometer cells with accuracies of less than 1 degree are commonly required for these consumer applications. Unlike low-cost consumer-grade inclinometer cells, MEMS sensors in inclinometers have an array of fine electrodes that improve the measurement's resolution and accuracy. The moving mass in the MEMS in inclinometers designed for static or near-static measurements is physically damped to limit the sensitivity of these sensors to frequencies exceeding 29 Hz.

MEMS tilt sensors are low-cost, robust, virtually immune to shock, and exhibit very good long-term stability. Biaxial tilt sensors contain two MES sensors oriented at 90 degrees to one another to allow perpendicular tilt measurement. They are readily adaptable for automated data acquisition, which allows a series of sensors to be continuously monitored for profiling purposes.

According to the American Institute of Architects (AIA), the construction sector in the US has been hit hard by the COVID-19 outbreak. The construction activity declined in 2020 and continued the same way through 2021. Construction activities are reduced by approximately 20% in the hospitality industry, 8% in the retail sector, and close to 11% in commercial offices. However, the construction of healthcare facilities and public safety surged in 2020. Industries that install higher volumes of sensor systems have been hit at various levels of degree by the COVID-19 pandemic. Construction, electronics, and automotive have been struggling due to concerns over contracting the virus, even after they could reopen. Similarly, the Canadian and Mexican tilt sensor market also witnessed the same and are experiencing similar tremors due to the COVID-19 outbreak. The commercial sector in the two countries has been witnessing significant shocks.

Based on material, the North America the tilt sensor market is segmented into metal and non-metal. The metal segment led the market with the largest market share in 2020 and is expected to register the highest CAGR during the forecast period.

By technology, the North America tilt sensor market is segmented into force balance, MEMS and fluid filled. In 2020, the force balance segment held the largest market share of the tilt sensor market. However, the MEMS segment is expected to register highest CAGR in the market during 2021-2028.

By industry, the North America tilt sensor market is segmented into mining & construction, consumer electronics, industrial, automotive and others. The mining & construction segment led the market with the largest market share in 2020, whereas the automotive segment is expected to register the highest CAGR during the forecast period.

A few of the companies profiled while preparing this report on the North America tilt sensor market are Parker Hannifin Corporation, TE Connectivity Corporation and Geosense.

Reasons to Buy

Save and reduce time carrying out entry-level research by identifying the growth, size, leading players and segments in the North America tilt sensor market.
Highlights key business priorities in order to assist companies to realign their business strategies.
The key findings and recommendations highlight crucial progressive industry trends in the North America tilt sensor market, thereby allowing players across the value chain to develop effective long-term strategies.
Develop/modify business expansion plans by using substantial growth offering developed and emerging markets.
Scrutinize in-depth market trends and outlook coupled with the factors driving the market, as well as those hindering it.
Enhance the decision-making process by understanding the strategies that underpin security interest with respect to client products, segmentation, pricing and distribution. Show more