Market Research Logo

Australian Procedure Numbers for Orthopedic Large Joint Devices 2016 - MedPro

Reconstructive implants are grouped into four broad categories: primary (total) replacement, partial replacement, resurfacing and revision.

Total joint replacement (TJR) involves replacing both sides of the natural joint. These devices are the most frequently used reconstructive procedures in the United States.

Partial joint replacements restore one side or a portion of the joint. These procedures have the advantage of preserving more bone and soft tissue but have historically been prone to a higher complication rate than total joint replacements. Partial replacement, also known as hemiarthroplasty, provides an alternative to joint fixation, or arthrodesis, in some instances of skeletal trauma.

Joint resurfacing attempts to preserve as much of the original bone stock as possible by placing a cap over the diseased joint surfaces. The cap is anchored by a short stem within the bone. These procedures are performed more frequently in younger patients, as the preservation of bone stock allows for better outcomes when the implant is eventually replaced later in life.

Revision implants are not a specific product type but refer to the replacement of implanted devices that have either reached the end of their useable lifespan or have become loosened through trauma or pathology. This may entail either the replacement of part of the implant or the entire implant. In general, revision implants require longer stems to anchor in the bone. Conservative estimates indicate that 15 years is an appropriate lifespan to expect from an implant regardless of its construction or method of fixation; however, newer devices are likely to exceed that time frame.

If anything, the trend towards younger patients has meant that the market has been even more mindful of preparing for the eventuality of revision because of the increased average lifespan for these surgical candidates.

Implants are subject to their own wear issues. Regardless of the type of construction, there are some basic safety concerns. Like the cartilage that it replaces, the articulating material is subject to wear. The concern remains with debris generation. While the material itself is inert, the body’s immune response to stray fragments creates the potential for osteolysis, the destruction of bone. There are similar concerns with devices using hard-on-hard articulating surfaces, as early ceramic materials were prone to chipping.


EXECUTIVE SUMMARY FOR COMPLETE ORTHOPEDIC LARGE JOINT REPLACEMENT SUITE
1.1 ASIA-PACIFIC ORTHOPEDIC LARGE JOINT REPLACEMENT DEVICE MARKET
1.2 TREND ANALYSIS BY SEGMENT
1.3 TREND ANALYSIS BY COUNTRY
1.4 KNEE REPLACEMENT DEVICE MARKET
1.5 HIP REPLACEMENT DEVICE MARKET
1.6 BONE CEMENT MARKET
1.7 COMPETITIVE ANALYSIS
RESEARCH METHODOLOGY
2.1 RESEARCH SCOPE
2.2 IDATA’S 9-STEP METHODOLOGY
Step 1: Project Initiation & Team Selection
Step 2: Prepare Data Systems and Perform Secondary Research
Step 3: Preparation for Interviews & Questionnaire Design
Step 4: Performing Primary Research
Step 5: Research Analysis: Establishing Baseline Estimates
Step 6: Market Forecast and Analysis
Step 7: Identify Strategic Opportunities
Step 8: Final Review and Market Release
Step 9: Customer Feedback and Market Monitoring
AUSTRALIAN PROCEDURE NUMBERS
3.1 INTRODUCTION
3.2 PROCEDURE NUMBERS
3.2.1 Total Large Joint Replacement Procedures
3.2.2 Knee Replacement Procedures
3.2.2.1 Total Knee Replacement Procedures
3.2.2.1.1 Total Knee Replacement Procedures by Cementation Type
3.2.2.1.2 Total Knee Replacement Procedures by Construction Type
3.2.2.1.3 Total Knee Replacement Procedures by Bearing Type
3.2.2.2 Partial Knee Replacement Procedures by Product Type
3.2.2.3 Knee Replacement Revision Procedures
3.2.3 Hip Replacement Procedures
3.2.3.1 Total Hip Replacement Procedures
3.2.3.1.1 Total Hip Replacement Procedures by Cementation Type
3.2.3.1.2 Total Hip Replacement Procedures by Bearing Type
3.2.3.2 Partial Hip Replacement Procedures by Product Type
3.2.3.3 Resurfacing Hip Replacement Procedures
ABBREVIATIONS
List of Charts
Chart 1 1: Orthopedic Large Joint Replacement Device Market, Asia-Pacific, 2012 – 2022 1
Chart 1 2: Orthopedic Large Joint Replacement Device Market by Segment, Asia-Pacific, 2012 – 2022 2
Chart 1 3: Orthopedic Large Joint Replacement Device Market by Country, Asia-Pacific, 2012 – 2022 3
Chart 1 4: Knee Replacement Device Market by Segment, Asia-Pacific, 2015 & 2022 4
Chart 1 5: Hip Replacement Device Market by Segment, Asia-Pacific, 2015 – 2017 5
Chart 1 6: Bone Cement Market by Segment, Asia-Pacific, 2015 6
Chart 1 7: Leading Competitors, Orthopedic Large Joint Replacement Device Market, Asia-Pacific, 2015 7
Chart 3 1: Orthopedic Large Joint Replacement Procedures by Segment, Australia, 2012 – 2022 22
Chart 3 2: Orthopedic Large Joint Replacement Procedures Breakdown, Australia, 2015 23
Chart 3 3: Orthopedic Large Joint Replacement Procedures Breakdown, Australia, 2022 23
Chart 3 4: Knee Reconstruction Procedures by Type, Australia, 2012 – 2022 24
Chart 3 5: Hip Reconstruction Procedures by Type, Australia, 2012 – 2022 30
List of Figures
Figure 3 1: Orthopedic Large Joint Replacement Procedures by Segment, Australia, 2012 – 2022 22
Figure 3 2: Knee Replacement Procedures by Type, Australia, 2012 – 2022 24
Figure 3 3: Total Knee Replacement Procedures by Cementation Type, Australia, 2012 – 2022 25
Figure 3 4: Total Knee Replacement Procedures by Construction Type, Australia, 2012 – 2022 26
Figure 3 5: Total Knee Replacement Procedures by Bearing Type, Australia, 2012 – 2022 27
Figure 3 6: Partial Knee Replacement Procedures by Product Type, Australia, 2012 – 2022 28
Figure 3 7: Knee Replacement Revision Procedures, Australia, 2012 – 2022 29
Figure 3 8: Hip Replacement Procedures by Type, Australia, 2012 – 2022 30
Figure 3 9: Total Hip Replacement Procedures by Cementation Type, Australia, 2012 – 2022 31
Figure 3 10: Total Hip Replacement Procedures by Bearing Type, Australia, 2012 – 2022 32
Figure 3 11: Partial Hip Replacement Procedures by Product Type, Australia, 2012 – 2022 33
Figure 3 12: Resurfacing Hip Replacement Procedures, Australia, 2012 – 2022 34
Figure 3 13: Hip Replacement Revision Procedures, Australia, 2012 – 2022 34

Download our eBook: How to Succeed Using Market Research

Learn how to effectively navigate the market research process to help guide your organization on the journey to success.

Download eBook

Share this report